2012 dodge journey bluetooth not working

[Solved] Dodge Journey Bluetooth Not Working (Simple Fix)

If you’re a Dodge Journey car owner, chances are that you have experienced some trouble with your Bluetooth connections. Whether it be connecting to the vehicle or staying connected, this can be a frustrating issue.

Fortunately, in this article there are several steps that you can take to troubleshoot and hopefully fix issues you may have with your Bluetooth connection in your Dodge Journey.

Why is Dodge Journey Bluetooth Not Working?

The first step is to understand why your Bluetooth connection may not be working. There are a few potential causes, so you must take the time to identify which one applies to you. Common reasons include:

Low Battery

Outdated software, interference from other signals, improper connection setup, faulty device firmware/software updates, bluetooth not activated or enabled on the device, incorrect pin or passcode entered.

• Incorrect Network Settings

The Device is Not Compatible with Bluetooth

Errors with the bluetooth connection, poor connection or signal strength, too far away from the bluetooth device, the device is paired with another device, the vehicle’s infotainment system needed resetting or updating.

The first thing to check is your device’s battery.

Make sure your device has enough power before trying to pair it with your Dodge Journey.

A low battery can prevent the connection from being established in the first place, or it can cause an existing connection to drop out.

Signs: You may see a message on your device that it is running out of battery.

Your device may also take longer than usual to connect or disconnect from other devices, such as headsets or car audio systems.

Solutions: Make sure that the device you’re trying to connect has enough power for a stable Bluetooth connection.

If the battery is low, charge it before attempting to reconnect with your Dodge Journey again. Once it is fully charged, you should be able to establish a connection.

Your device may also be running an outdated version of the software, which can prevent the connection from being established in the first place.

Visit the manufacturer’s website and download any available updates for your device.

Signs: You may notice that your device is displaying an error message or a warning message that it is out of date.

Solutions: To ensure a stable connection with your Dodge Journey, make sure that the software on both devices is up-to-date.

Check for any available updates on your device’s settings page and then attempt to reconnect with your Dodge Journey once the updates have been installed.

• Go to your car settings and select the “Bluetooth” option.
• Select “Update Software”.
• Follow the instructions on the screen to complete the update process.
• After the update is complete, try connecting your device again.

If you are still having issues, try restarting your device or your car’s Bluetooth system.

After troubleshooting, you should be able to successfully connect your device to the Dodge Journey’s Bluetooth system.

Sometimes, interference from other signals can disrupt the Bluetooth connection.

Wireless networks and other Bluetooth devices nearby can block the connection of your Dodge Journey. This interference is especially common in areas where wireless signals are dense, like airports or busy urban streets.

Signs: Your Dodge Journey may experience the following signs of interference: Bluetooth connection drops intermittently, Slow or choppy audio transmission and Inability to connect to other devices.

Solutions: Fortunately, there are measures you can take to reduce this kind of interference and hopefully restore your Bluetooth connection.

To start, try moving away from any electronic devices that might be causing disruption. You can also change the frequency of your Bluetooth connection to a less congested channel.

To avoid this issue, make sure that you are not in an area with a lot of wireless activity. It is also best to turn off any Wi-Fi networks or cellular connections while attempting to connect your device to the Dodge Journey.

If the Bluetooth device is not properly connected to your Dodge Journey, you may experience issues with its connection.

Signs: Improper setup can lead to problems such as slow audio transmission or inability to connect other devices.

Your Dodge Journey might also display the following signs of an improper connection setup – difficulty connecting with other devices, inadequate audio streaming quality and unreliable connection.

Solutions: To fix this, check the connection settings of your Dodge Journey’s Bluetooth device. Make sure that both devices are properly paired and all the necessary settings have been enabled.

Additionally, try toggling the Bluetooth on and off to reset its connection to your vehicle.

It is also possible that the Bluetooth device’s firmware or software has been updated incorrectly, resulting in a faulty connection with your Dodge Journey.

Firmware are programs pre-installed in a device that control how the device functions. While software updates are commonly used to improve the performance of a device, but if an incorrect version is installed, it could lead to connectivity issues.

Signs: Incorrect updates will often lead to errors such as slow audio streaming, inability to connect to other devices and unreliable connections.

Solutions: To fix this issue, you should first update all necessary drivers on your Dodge Journey. Additionally, reset the Bluetooth device’s settings and try again. If this fails, you might need to manually update the firmware/software of your device.

You must always check for updates on both devices before connecting them. This will ensure a more stable connection with better audio streaming quality.

Steps to Update the Software of Dodge Journey Bluetooth:

• Start by connecting the device to your Dodge Journey’s Bluetooth system.
• Go to the device’s settings and locate the ‘Software Update’ option.
• Select ‘Update Software’ and follow the on-screen instructions accordingly.
• Wait for the download to finish before disconnecting the device from your Dodge Journey.
• Now turn off the device and restart it for the new software update to take effect.
• Turn on your Dodge Journey’s Bluetooth again, and make sure that your device is now connected properly.

If the Bluetooth on your device is not enabled or activated, you won’t be able to connect it to the Dodge Journey.

Signs: You will know that Bluetooth is not activated or enabled on your device when you don’t see the Bluetooth icon in your Settings menu.

You should also check whether your device has a version of software that supports Bluetooth connections, as this may affect your ability to connect to the Dodge Journey.

Take Time to Pair Your Device with the Vehicle as it can take several minutes to pair your device with the Dodge Journey, so be sure to give it enough time.

Once you’ve ensured that your device and vehicle are both on and ready to pair, select the “Pair” option from the Bluetooth menu of your device.

You may need to enter a code provided by the vehicle before the process is complete.

To enable or activate Bluetooth on your device, please take the following steps:

• Open “Settings” on your device.
• Select “Bluetooth” in the settings menu.
• Ensure that the Bluetooth feature is toggled ON and visible.
• Go back to the main Settings page and select- “More” to access additional settings.
• Select the option to enable or activate a Bluetooth connection with the vehicle.

You should now be able to connect your device using Bluetooth when in range of the Dodge Journey. Be sure to check that you are within range for it to work properly as this can also affect connection and sound quality.

If the incorrect PIN or passcode is entered when trying to pair your device with the Dodge Journey, it will not be able to connect.

Solutions: To resolve this issue, try deleting and re-pairing your device using the correct code. You can also reset both the vehicle’s Bluetooth connection and that of your device to ensure that the pairing process runs as smoothly as possible.

With a few simple steps, you should now be able to troubleshoot any Bluetooth connection issues with your Dodge Journey.

Incorrect Network SettingsIf incorrect network settings have been applied to your device, it could prevent it from connecting to the Dodge Journey via Bluetooth. To ensure that this isn’t the issue, try resetting the network settings on both your device and vehicle.

To reset the network settings of your device, follow these steps:

• Go to “Settings- Select the option to “Reset Network Settings”
• After resetting your device’s network settings, repeat this process for the vehicle.

This should ensure that all networks associated with your Dodge Journey are properly set up and ready to connect via Bluetooth.

Sometimes, the device you are trying to connect may not be compatible with the Dodge Journey. To avoid any issues arising in this case, always check that your device is Bluetooth-capable and also has the correct version of Bluetooth installed (if applicable).

Solutions: To make sure your device is compatible with the vehicle’s Bluetooth connection, take the following steps:

• Look up the version of Bluetooth your device is compatible with and make sure it matches the version installed on the Dodge Journey.
• If you find that your device is not compatible, try connecting a different device with one that is compatible.

By taking these measures, you can ensure that any incompatibility issues between your device and the Dodge Journey are addressed.

If you have verified that both your device and the Dodge Journey have compatible Bluetooth versions, but the connection still isn’t working, then there may be some errors occurring on the vehicle side of things.

In some cases, you may encounter error codes when attempting to connect your device to the Dodge Journey via Bluetooth. Some common error codes that can appear include ERROR-11, ERROR-14 and ERROR-17.

Each of these error codes is associated with a different issue relating to the Bluetooth connection and needs to be addressed differently to establish a successful connection.

Solutions: To diagnose this issue, try restarting your car and completely disconnecting any other devices from its Bluetooth connection.

Once this is done, try connecting your device again and see if the connection works.

On certain occasions, the connection between your device and the Dodge Journey may be weak or unreliable. This can occur if the vehicle is located too far away from your device, or if there are any obstructions in the way of the signal (e.g. walls or furniture).

Poor connection between devices may be indicated by several symptoms, such as choppy audio playback, music skipping or interruption in streaming.

It can also lead to slow data transfers between the two devices and even disconnection when attempting to make calls.

Solutions: If you encounter any issues with poor signal strength, try moving closer to the car or relocating any obstructing objects to improve the signal strength.

You can also try connecting via an external device such as a Bluetooth dongle or a car phone holder, which may help to provide a more reliable connection.

Sometimes, your Dodge Journey might be too far away from your device for a successful connection. This is especially true if you leave the car outside while attempting to connect your phone.

Signs: The symptom of being too far away will be noticed when you try to connect your device, but it does not appear in the list of available Bluetooth devices on your phone. Additionally, if the connection is successful, it may be unreliable and suffer from poor signal strength.

Solution: To ensure that a successful connection is made, make sure you are within range of the Bluetooth device before attempting to connect.

Your Dodge Journey may be paired with another device, such as a laptop or tablet, and thus unable to pair with a new device.

Signs: This symptom will usually manifest itself when you cannot find your device in the list of available Bluetooth devices on your phone. Additionally, sometimes the connection is successful but episodic and unstable.

Solution: To solve this issue, go to the settings page on your Dodge Journey’s infotainment system and delete any existing pairings before attempting to connect with a new device.

If these solutions do not work for you, try resetting that causes Dodge Journey Bluetooth not to work, The resetting process for your Dodge Journey’s Bluetooth can be done within the infotainment system.

To do this, go to Settings and then navigate to Network & Connectivity. From there, you should see an option that lets you “Forget” any existing pairings. Select that option and then reboot your device before trying to connect again.

If the above solutions do not work, it may be necessary to reset or update your Dodge Journey’s infotainment system. This can often resolve any issues with Bluetooth connectivity.

Signs: This symptom can manifest itself when your device is paired successfully but the connection is unstable or constantly dropping.

Other signs include if the infotainment system takes too long to respond to commands or does not recognize your device altogether.

Solution: To solve this issue, try resetting your vehicle’s infotainment system. You can do this by accessing the Settings page and going to System Updates.

From there, you should see an option that lets you “Check for Updates”. Selecting this will allow you to install any necessary updates and should fix your Bluetooth connection issues.

If these solutions are not successful, try rebooting the infotainment system. This option is also available on the System Updates page. Select “Reboot” and wait for the system to restart before attempting your connection again.

How do you reset the Bluetooth in a Dodge Journey?

If you’re having problems with the Bluetooth in your Dodge Journey, a simple reset may help. Here are the steps on how to do it:

• Start by turning off both your phone and the vehicle’s Bluetooth connection.
• Next, open up the Settings app from your phone and select Bluetooth.
• Then, turn off or disable all Bluetooth devices that are currently connected.
• Finally, restart the vehicle and then your phone, and then try connecting to the Dodge Journey’s Bluetooth system once again.

If this reset doesn’t work, it might be worth taking a look at the user manual for further troubleshooting steps related to your Dodge Journey’s Bluetooth system.

It may be that you need to visit your local dealership for deeper diagnostics and repairs.

In conclusion, If all the troubleshooting tips fail, contact an authorized service center for further assistance and professional evaluation of the issue.

They are well-versed in Dodge vehicles and have the necessary tools to diagnose and repair any issues with your vehicle’s Bluetooth

You can also contact the dealer or manufacturer for assistance if you are unable to find a solution. They may be able to provide further advice and help guide you through the process of getting your Dodge Journey’s Bluetooth working again.

Ultimately, it is important to take the necessary steps to get your device running again to stay safe and connected while driving.

Dodge Journey: How To Reset UConnect

If your Dodge’s infotainment screen or system is glitching or freezing out, don’t fret. Bad updates, overloaded memory, or temporary electrical issues can all cause the system to temporarily bug out.

Luckily, you can reset the UConnect system or the car’s electronics to remove the most common issues.

How to Reset UConnect in Dodge Journey

Ever since the second major release of UConnect, the system can be soft reset solely through the infotainment buttons on the console. You’ll need to turn on the vehicle, but it’s recommended to keep the engine off. Here’s what you need to do:

• Press and hold the “Volume” and “Tune” buttons on the infotainment system.
• Wait until the screen goes blank or displays the Dodge logo.
• Release the buttons and wait for a bit.
• The system should automatically restart, displaying the Dodge logo and other startup information.
• You can now use the infotainment system normally.

For the oldest version of UConnect, it’s best to turn off the car, wait a few minutes, then turn it on again.

In newer vehicles, you can also find a second option for soft-resetting the system:

• Press and hold the “Up” and “Down” arrows on the console (for climate controls). In some cars, you may need to press the “Phone” and “Mute” buttons at the bottom of the console.
• Wait until the “Engineering Menu” shows on the screen.
• Use the scroller on the screen to go to “Reset to factory settings.” You can also choose to reset the radio (“Reset radio”) only if that’s your primary concern.
• Select the option on the touchscreen, then hit “Yes” to confirm.

This option won’t work if the screen itself is unresponsive, but it completely removes previous settings and updates that may be messing with the system.

How to Reset a Dead Infotainment System

If the entire infotainment system is unresponsive and the screen is completely black, then it may have blown a fuse or another electrical component.

The fuse box for Dodge Journeys is typically located under the glovebox. It has a lid that opens by hooking one finger into the gap and pulling. The lid should also have a printed or etched fuse box plan inside.

You need to replace the 10A fuse in the second row of fuses (second on the right). Turn off the car before pulling the fuse and check it with a multimeter to ensure it’s actually blown. Consult the fuse plan on the lid or the owner’s manual to ensure you’re replacing the correct fuse.

If the fuse is not blown, put it back into the box and try to start the radio system. If that still doesn’t work, you may have a deeper electrical issue that warrants a professional inspection.

Reset the System by Draining the Car

As a last resort, you can remove the battery for the car and drain its electricity to hard reset the UConnect system:

• Open the hood.
• Remove the cables from the battery (starting with the negative).
• Honk the horn or turn on the headlights to drain the battery completely.
• Wait for a few minutes.
• Reconnect the battery cables (positive first this time).
• Start the car and check the infotainment system.

What If the Screen Is Different?

In some cases, resetting the system will change how your infotainment screen and options look. That’s because factory settings will likely revert UConnect to an older version with a different UI. Typically, leaving the car alone for a few minutes with an active internet or cellular connection will prompt it to download the latest UConnect version and fix the issue.

If this doesn’t happen, navigate to “Settings” on the screen and select “Software Update.” This option has been relocated on the display a few times on different UConnect versions and may also be named differently depending on the version. You can typically find the current version number at the bottom of the screen while the system boots. Check the UConnect website for the operating manual for that specific release.

Was this helpful?

Related posts:, 23 thoughts on “dodge journey: how to reset uconnect”.

This absolutely did not work

Doesn’t work

Same, did not work on my radio

My Dodge Journey Uconnect still down or no operationnal

It should be in your manual.

I have my manual and it says nothing

Did not work and this is very frustrating

did not work for my 2013 dodge journey sxt still can’t connect to bluetooth very sad

How do I preset radio station in 2015 dodge journey

Tried to reset my uconnect but the procedure I found did not work. Still uconnect is unusable. Haven’t been able to use my unconnected for over 2 years and yet Dodge wants to charge me over $200 to fix it because it’s supposedly the module. Dodge should add this problem as a defect. Angry, frustrated 🤬😡

I agree, we pay a lot of money for these options and I am tired of the vehicle industry just washing their hands of their responsibilities to their clientele.

I sold my 2019 dodge charger after 6 months because of this issue, I drive to much for something so trivial to irritate me every single day. Took it in multiple times to get it fixed and the dealer couldn’t/wouldn’t fix it.

That’s hilarious. Up here in Canada it cost me over $1000 to replace. Then it went out a couple of months later.

My 2015 Journey crossroad’s uconnect will not come on after I start the vehicle until a few miles down the road. this happens mostly during cold weather; vehicle is garage kept.

I found a loose connection in the back of my 8.4 uconnect screen that was loose which caused it not to come on or sometimes go out and back on. I pulled all connections apart sprayed some electrical cleaner on them and replaced the connection, haven’t had any more problems sense. Search on You-Tube for instruction on how to remove the device.

I NEED A “HARD” RESET!!! NOBODY GETS THIS??? WILL NOT WORK AFTER FIRESTONE REPLACED BATTERY!!!

Uconnect is GARBAGE. It got corrupted during the update process! NAV never worked since.

Same for me. Don’t know what I can do now, feel certain it’s software not hardware!

I have follow the steps but my dodge journey sxt 2016 uconnect is not connecting

2016 Dodge Journey USB works with IPOD, but not bluetooth. Smartphone connects to Uconnect via bluetooth with no problem, weird thing is, my 2013 Dodge Avenger has no problem via blue tooth with smartphone or Ipod.

I got my self a aux/bt wireless connector / adapter that I plug on the aux input under the armrest with USB power connect my phone and there we go.. Bye bye frustration go away.. Costs me 8 bucks…

I bought a rt model in germany not long ago, the same, total crap, I read everything possible, even about fuse 131,128, total shit, as written above, software sucks from 2012 to 2016 unconnect crap,

Well I have no hope now, having g same problem, I’m not paying for the to fix this bs, guess I just use my bt speaker in car smh

Leave a Comment Cancel reply

• Fuel Consumption
• Engine Sizes
• Engine Torque
• Engine Power
• Towing Capacity
• Seating Capacity
• Steering Wheel Size
• Dimensions and Weight
• Fuel Tank Sizes
• Trunk Space
• Tire and Rim Sizes
• Bolt Patterns
• Coolers and radiators
• Radiator Fan
• Heat Exchanger
• Intercooler
• Timing Belt
• Sizes of Wiper Blades
• Cabin Filter
• Fuel Filter
• Transmission Fluid
• Antifreeze & Coolant
• Brake Discs
• Brake Drums
• Brake Fluid
• Bulbs For Fog Lights
• Bulbs For Headlights
• Bulbs For Turn Signals
• Bulbs For Licence Plates
• Bulbs For Markers
• Bulbs For Rear Fog Lights
• Bulbs For Backup Lights
• Bulbs For Brake Lights
• Technical Specs
• Car History

• Engine & Fuel
• Coolers and Radiators

Dodge Journey: Bluetooth Not Working. What's the Problem and How to Fix?

CarAraC auto mechanics and car experts

The Bluetooth function enables you to listen to your favorite music, audiobooks, or podcasts while on the road. Most Dodge Journey models use the Uconnect system to connect to your mobile device. Your trips become boring when Bluetooth stops working.

The problem may start with your device or the Uconnect system. In this article, we look at all the possible reasons why Uconnect Bluetooth may stop working. We will also provide quick fixes to bring back exciting road trips.

Reasons Why Your Bluetooth Is Not Working

Pairing your phone with the Uconnect system may fail because of phone or system glitches. The problems are usually easy to fix if you have installed an updated Uconnect version. The common reasons why Uconnect fails are a weak signal, phone bugs, faulty connections, and system bugs.

1. Poor Signal Strength

The Uconnect system will not connect with your device if the signal strength is poor. You can test the signal strength from the Uconnect website. Provide your vehicle model and year in the search bar. Check the signal strength following the instructions given. You can determine if the signal is poor, fair, or strong for your Dodge Journey model.

2. Uconnect Has a Problem

Uconnect can suffer issues or bugs like any other software, leading to pairing problems with other devices. You cannot diagnose the problem or fix a bug with the system. However, resetting and updating Uconnect fixes some bugs.

3. Your Phone Is Not Connected Properly

The Uconnect system may fail if your phone is not connected well. Sometimes the device fails to complete the pairing process, especially if it has been connected to other devices. In addition, you may have skipped some security checks and auto prompts when connecting to the Uconnect system. Consequently, the phone blocks any pairing attempts.

The auto-accept and security prompts are different for each phone model. Restart the pairing process to verify all the checks. The problem could also be with the Bluetooth settings on your phone. Reset the phone to enable wireless connections with other devices.

4. Device Malfunctions

The Bluetooth function on your phone may be working properly, but the device has other bugs or glitches. Malfunctions may cause the phone to suspend all operations as it tries to reboot the system. Restarting the device will fix the glitch.

Network problems and pending system updates may also cause Bluetooth to malfunction. Check if your network is working well and reset it, if necessary. In addition, check for any operating system updates that you may have skipped and install them.

What to Do When Your Uconnect Bluetooth Is Not Working

You can fix most Bluetooth problems without calling your mechanic or car dealer. However, you must ensure that the solutions you attempt apply to your car and phone model. For instance, each car model has different instructions for resetting the Bluetooth function and installing updates. This guide discusses the solutions that work for most Dodge Journey models.

1. Ensure That Your Phone is Discoverable

You may have trouble with the Bluetooth connection if Uconnect cannot find your phone. Confirm that your phone is discoverable before checking other functions. The process is simple. Open the Bluetooth settings on your device and turn on the "discoverable" mode.

The terms may differ depending on your phone model, but the point is to ensure that other devices can find and connect to it. In addition, ensure that the security settings allow you to use Bluetooth and other external connections.

2. Restart Your Phone

Sometimes fixing the Bluetooth connection problem is as simple as restarting your device. If your phone is discoverable but not pairing properly with Uconnect, power it off or remove the battery for a few minutes, and then turn it on. Restarting the phone resets the Bluetooth function, enabling other devices to connect easily.

Restarting the devices also fixes any other glitches and prompts you to install the latest updates. If restarting does not activate the Bluetooth function, you can reset the phone to factory settings. Save any data that you may lose in external storage before resetting the phone to factory settings.

Another tip is to close other running apps that slow down your phone. For instance, you may be trying to play music through an app with bugs. Limit the number of running apps when pairing the phone with Uconnect and check if the connection is better.

3. Clear the Pairing History

After restarting the phone and closing unnecessary apps, delete the pairing history on your phone and vehicle. Go to the Bluetooth settings on your phone, trace the Uconnect connection, and delete or forget it. You need to do the same on the Uconnect system on your Dodge Journey.

You can reset the Bluetooth connection in the vehicle by turning off the ignition key for a few seconds and turning it back on. Alternatively, you can follow these steps to delete the pairing history:

• Open the Uconnect settings on your car's display unit and then tap the Connections button.
• Scroll down the connections list to identify and select your phone.
• Locate the option to "Delete All Pairing History."
• Select "Delete" on the pop-up menu.

Ensure that the phone is discoverable and reconnect the two devices again. If the connection is unavailable or poor, follow the other troubleshooting instructions below.

4. Disconnect Other Devices

The Uconnect Bluetooth system cannot connect to your phone if it is connected to another device. You or your passenger may have paired Uconnect with other devices unknowingly. Disconnect any other device first before pairing it with your preferred phone.

In addition, go to Bluetooth settings on your phone again and forget any other paired device. Connect your phone to the Uconnect system in your Dodge Journey again and test the strength of the connection.

5. Install Uconnect Updates

Uconnect developers release occasional software updates for different car models. The updates improve your experience and fix any bugs in older app versions. An outdated version may be slow to connect with your phone.

Visit the Uconnect website and search for the latest updates for your car model. In this case, enter your Dodge Journey year in the search bar. Download and install any updates using the instructions given. It is advisable to check for updates regularly, even when the app is working for the best user experience.

In most cases, you need at least 4GB of storage space on a USB drive to save the updated software on your computer. Plug the USB drive into your vehicle's infotainment center. Start the car and keep it in the run position.

Follow the prompts and provide the anti-theft code, which is available from an authorized dealer. The anti-theft code protects your car and its systems from breaches. In addition, installing all the latest updates ensures that the Uconnect system works at its optimal performance always.

Uconnect updates are free. The free version has the features you need to start the engine, lock the doors, activate the horn, and turn on the lights. However, you can upgrade your subscription to access premium features, such as stolen vehicle assistance, drive rating report, or roadside assistance call.

6. Reset Uconnect

Another simple solution is to reset the Uconnect system, especially when other troubleshooting tips do not solve the problem. The reset steps vary with the Uconnect version.

• Turn on the ignition key on run mode and leave the vehicle in park.
• Press and hold the Bluetooth connection or phone button for about 30 seconds and then release it. The display terms differ with the car model. Some models require you to simultaneously press the tuner knob and volume button for about 20 seconds. Accept any prompt to restart or reset the system.
• The screen will display the vehicle brand and then go off for some time.
• The display screen will show your vehicle brand again. Uconnect will restart and reset itself to the default settings.

The system will take you back to the main screen, where you can repair your phone. It is advisable to reset the system often to keep the connection strong.

7. Contact the Customer Service or Car Manufacturer

The tips shared here fix most of the Bluetooth issues. However, you can seek further assistance from Uconnect if the problem persists. The customer service is helpful with poor signal strength when resetting the system does not improve the connection.

If Uconnect customer support confirms that the signal is strong, check with your car manufacturer or dealer for an alternative solution. The car system may have security checks that hinder connections with third-party software.

Bluetooth may stop working if the Uconnect signal is poor or the software glitches. Malfunctions in your phone, including slow apps and a poor network connection, can cause Bluetooth problems. In addition, the pairing process may fail if you skip some security checks and auto-accept requests. Restarting your phone may solve glitches and reset the Bluetooth function.

You can reset the Uconnect system and install the latest updates for your Dodge Journey model for better performance. The Uconnect website lists all the updates and instructions for car owners to update their software. You can also upgrade your Uconnect subscription to enjoy premium features.

About the authors

The CarAraC research team is composed of seasoned auto mechanics and automotive industry professionals, including individuals with advanced degrees and certifications in their field. Our team members boast prestigious credentials, reflecting their extensive knowledge and skills. These qualifications include: IMI: Institute of the Motor Industry, ASE-Certified Master Automobile Technicians; Coventry University, Graduate of MA in Automotive Journalism; Politecnico di Torino, Italy, MS Automotive Engineering; Ss. Cyril and Methodius University in Skopje, Mechanical University in Skopje; TOC Automotive College; DHA Suffa University, Department of Mechanical Engineering

Add comment

• Forum Listing
• Marketplace
• Advanced Search
• General Charger Forums
• Dodge Charger News

Uconnect / Bluetooth not working/ This might be your Fix

• Add to quote

I hope this will help somebody. I have a 2012 Dodge Charger SXT & my Uconnect/Bluetooth quit working about 2 months ago. I researched online to see if there was a way for me to fix it myself. Alot of ppl are having the same problem with Dodge. I tried all the tricks. Nothing worked. The one thing I didn't want to do was to replace it completely like other ppl had to & costing around $700. Meanwhile every now & then the battery saver mode would pop up on my messages/dash which had me worried so I went & had my battery tested. I had it tested for free at Advanced Auto Parts. My battery read good but stated it needed to be charged yet my alternater was good which I knew bc it was replaced by a recall not long ago. I still had the original battery that came with the car. So the man said maybe it's about to go bad & that's why it's not getting/holding a full charge. I mean it is 7 yrs old. So I went today to the Dodge Dearlership near me to get it replaced bc no Auto parts store will install it..believe me I went to multiple different part stores..all bc it's in the trunk & the parts stores won't let them install them bc it's around cables & wires that's a little more complicated they say & puts them at risk of messing stuff up. It states they can't install it on their computers when looking it up for my car also. Anyway my husband read online somewhere when researching my Uconnect problem that if your battery doesn't have full power that some of your electronics will stop working. I knew I needed a battery anyway. My car always cranked & I never needed a jump but just going off the battery saver mode notification & looking up what it meant.. I got worried recently when I saw a video of a man stating don't let your battery completely die in your Charger. Bc nothing will work then. You can't pop the trunk to get to your battery then. He had to climb through the back seats to try to get to the trunk & I don't remember how he got the trunk open but put it this way..you don't wanna have to do it.. After replacing my battery today..my Uconnect/Bluetooth is back working. Dealerships or Service writers aren't gonna tell you if that might be your problem bc everybody's trying to make money. Money to replace a module plus labor vs a battery replacement. Not saying this is always the case but it was my case. So if your battery isn't working as good as it should be then that's probably your problem. Just get your battery tested for free first to see if it's good & charging completely. If it's saying you need to charge it then have them test your alternater for free if it's good then you might need to get a new battery like I did just so everything works like it's supposed to. If that's not your fix then maybe it's the module.  

The "battery saver mode" message is a warning that your battery is not able to keep up the demands being put on it. I always interpret it as a early warning message telling you to replace the battery. When the "Battery Saver Mode" or “Battery Saver On" message is displayed, the vehicle will turn off certain electrical functions to reduce battery energy consumption. This will occur during periods when the battery is not being adequately charged or the battery is not capable of keeping up with the demand . During this time, the following features (if equipped) may be turned off or will operate at a reduced power level: heated seats and heated steering wheel, heated or cooled cup-holder, rear defroster and heated mirrors, heating and air conditioning, power inverter, audio and telematics system. .  

djalbin said: The "battery saver mode" message is a warning that your battery is not able to keep up the demands being put on it. I always interpret it as a early warning message telling you to replace the battery. When the "Battery Saver Mode" or “Battery Saver On" message is displayed, the vehicle will turn off certain electrical functions to reduce battery energy consumption. This will occur during periods when the battery is not being adequately charged or the battery is not capable of keeping up with the demand . During this time, the following features (if equipped) may be turned off or will operate at a reduced power level: heated seats and heated steering wheel, heated or cooled cup-holder, rear defroster and heated mirrors, heating and air conditioning, power inverter, audio and telematics system. . Click to expand...

If your new battery goes dead, the problem is the telematics module itself. I had the exact same problem on my Journey, battery tests good but needed replacing. Replaced it and everything was good for a few months. Then it died again, Pulled the fuse for the Telematics module and battery charged up and worked fine for months. Reconnected fuse and battery got weak again. You may have just bandaided the problem with a new battery, if your car sits for more than 5 days you may find a low battery if the module is bad.  

Pulled the fuse for the Telematics module and battery charged up and worked fine for months. Reconnected fuse and battery got weak again. Click to expand...

Update..since replacing my battery.. I'm back to every now & then my Uconnect not working. I gave up checking to see if it worked about a week ago. Something told me to check it yesterday & surprisingly it worked but today...not working... Ugh! When replacing my battery I wanted to get a more powerful battery but was limited on space since it's in the trunk & had to get it installed at a Dodge Dealership bc regular auto parts stores won't touch it. Costing me $65 for the installation. I saw YouTube videos of ppl getting better batteries that could handle all the electronics but was discouraged when I was told they wouldn't fit properly yet I saw them being installed by Charger owners. Maybe they customized their trunks idk. Anyway I'm back to square one. Lol maybe I need to research the telematics module. Thanks for the replys. ?  

The non-Police Chargers have either a 160A or a 180A alternator. The Police Chargers have a 220A alternator. A higher amp alternator has an easier time of keeping the battery fully charged. There is only one factory Mopar spec battery for the non-Police Chargers. This is probably why the dealership only offered one option. Any battery you install should meet the factory spec so that the battery will fit correctly. For 2012 ... BCI Group Size = 94R The outside dimensions and terminal placement of the battery conform to standards established by the Battery Council International (BCI). Each battery is assigned a BCI Group Size number to help identify a correctly-sized replacement. Cold Cranking Amperage = 730 Reserve Capacity = 140 Ampere-Hours = 72 Since the battery is in the trunk it needs to be vented to the outside. There's a vent tube in the trunk that plugs into the battery. You need a battery that has a vent hole properly located so the vent tube can plug into it. None of this helps with the telematics module but it does explain why the auto parts stores didn't want anything to do with the battery and why the dealership only had one battery choice. You can look at the Build Sheet (Equipment Listing) for you car and see what alternator was installed at the factory. The link is https://fcacommunity.force.com/RAM/s/equipment-listing Enter the VIN in all CAPS if you get a message that says the VIN could not be found. You need a healthy alternator to keep the battery healthy. You can check to see if your car was included in the FCA alternator recall. The link is https://www.mopar.com/en-us/my-vehicle/recalls/search.html .  

• ?            
• 105.4K members

Top Contributors this Month

NOW OPEN – DIRECT CONNECTION BROUGHT TO YOU BY DODGE POWER BROKERS

• Shop Parts & Accessories
• ®</sup>" role="button">Learn About Uconnect ®
• View Owner's Manual
• Pair Your Smartphone
• Purchase EV Charger
• Shop Merchandise
• EXPLORE FAQs
• FIND A DEALER
• SCHEDULE SERVICE

UCONNECT ® PHONE PAIRING INSTRUCTIONS

Shop for your next vehicle.

• Roadside Assistance
• For First Responders
• Chat with Us
• Find a Dealer
• Owner's Apps
• Owners Manual
• Maintenance Schedule
• Warranty Information
• Parts & Accessories Catalogs

For Dealers

• &reg;</sub> Repair Connection">Mopar ® Repair Connection
• &reg;</sub> Dealers">Mopar ® Dealers
• &reg;</sub> CAP">Mopar ® CAP
• DealerCONNECT
• Legal, Safety & Trademarks
• Terms of Use
• Accessibility

Privacy Center

• Privacy Policy
• Manage Your Privacy Choices
• Cookie Settings

SERVICE SCHEDULING MADE EASY

Conveniently book an appointment with your preferred dealer

Did you know creating an account allows us to save vehicle information and preferences so future bookings are even simpler? Register Now

• © 2024 FCA US LLC. All Rights Reserved.
• Chrysler, Dodge, Jeep, Ram, Mopar, SRT and HEMI are registered trademarks of FCA US LLC.
• ALFA ROMEO and FIAT are registered trademarks of FCA Group Marketing S.p.A., used with permission.
• FCA US LLC strives to ensure that its website is accessible to individuals with disabilities. Should you encounter an issue accessing any content on Mopar.com, please email our Customer Service Team or call 1-800-399-2668, for further assistance or to report a problem. Access to https://fcagroup.my.site.com/Mopar/s/knowledge?language=en_US is subject to FCA US LLC’s Privacy Policy and Terms of Use.

Select a vehicle to explore. Sign in (or create an account) to receive access to even more exciting content

Your preferred dealer has been successfully updated.

Your preferred dealer has been successfully updated, thanks for visiting.

You are now leaving the Mopar ® U.S. site and will be logged out of your account.

modal title

One moment please.

CarComplaints.com : Car complaints, car problems and defect information

Latest news.

• Apr 27: Mazda Class Action Lawsuit
• Apr 27: Tesla Autopilot Safety Recall Investigated
• My Account |
• Investigations
• Search Complaints
• Update Carcomplaints
• Add Complaints
• Recent Trends
• Best Vehicles
• Worst Vehicles
• Worst Complaints
• Dodge »
• Journey »
• 2012 »
• accessories - interior
• Lamborghini
• Mercedes-Benz
• B2500 Cargo Van
• Conversion Van
• Grand Caravan
• Power Ram 50
• Ram 2500 Power Wagon
• Ram Conversion Van
• Ram Van 1500
• Ram Van 2500
• Ram Van 3500

Uconnect Not Working

2012 dodge journey.

This problem may be covered under warranty. Ask your Dodge dealer.

• « back to accessories - interior
• Complaints 679
• Crash Tests 2
• Journey Recalls 6

Most Common Solutions:

• replaced telematic module (4 reports)
• not sure (3 reports)

accessories - interior problem

Unsubscribe any time. We don't sell/share your email.

Helpful websites

• No one has added a helpful site for this 2012 Journey problem yet. Be the first!

Find a good Dodge mechanic

A free service from CarTalk.com

Search for Car Problems

Example: "Bad Brakes", "Toyota Recall", etc.

2012 Dodge Journey Owner Comments

Dec 01 2016

• Automatic transmission
• 47,250 miles

A D V E R T I S E M E N T S

WTH, this seems to be a common problem. I hate Dodge

- Vickie E. , Pensacola, FL, US

Apr 01 2015

Journey SXT V6

• 44,000 miles

Of course the warranty had JUST expired, so it will cost me $ to get it fixed.

- Ann E. , Kent, WA, US

Feb 10 2015

Journey SE Plus 2.4L

• 38,525 miles

Just after warranty expired. Very Convenient! I'll give the dealer props, though. They also replaced the cable at no charge, gave me a loaner for the day while the part was being ordered (they had to take apart the console to get to it.). Also knocked 15% off the bill. It every now and then has connectivity issues but it fixes when I unplug my iTouch & plug it back in.

- Mark W. , Toronto, ON, Canada

Oct 07 2015

Journey Crew 3.2L V6

• 76,000 miles

I have had my 2012 Journey Crew serviced 3 times for the same issue. Next week will be the 4th time. The handsfree system is stuck. "Handsfree system updating .. please wait". The dealer has replaced the radio/computer module too. There's no error code so they cannot pinpoint the problem and I honestly don't think this thing can be fixed.

- Gina H. , Omaha, US

Dec 04 2015

Journey SXT

• 57,259 miles

This is now the 3rd time that I have had it in for the radio control issues and now this time issues with the Bluetooth not working. They replaced some module that was suppose to take care of everything. They were able to connect to the Bluetooth and it all seemed to be working for them. I left that afternoon with it, tried to connect my phones Bluetooth would not connect and then the next morning issues again with the radio controllers on the steering wheel. I am beyond irritated with this bullshit. 3 times in for the same thing and NO FIX, so glad that we purchased an extended warranty on it. Will be taking it back and this time I will not be paying the deductible on the warranty and expect some compensation for this

- Christine L. , Paynesville, MN, US

Search CarComplaints.com for these popular complaint phrases...

Aug 01 2014

Journey SXT 3.6L V6

• 47,000 miles

Same as another person I've seen complain about it, my touch screen radio sometimes just doesn't come on. some times you start the vehicle, the screen comes on, shows the radio is on, but no sound. you touch a button and it gives what I call a failure sound. Turn the car off, and then back on and it is fine. It does this ever so often, like whenever it feels like it. Don't know what to do. I'm not paying Dodge to put in another radio, but I will mention it to them again. Funny enough, it never does it in front of 1 of their Techs!! Waits till I get it home or somewhere else. Of course, Dodge says they can't fix it if they don't see a problem.

- Andre G. , Cicago, IL, US

Jul 29 2013

Journey ES 2.0L

• 20,394 miles

I will never buy another US made car again. Junk! And the dealers are an embarrassment and joke. They stand there and lie to your face and expect you to just suck it up and let them rip you off. Ah...how about NO!

- dunnwithuscars , Providence, RI, US

DON'T WASTE YOUR TIME: Link must be about this specific problem or it will be deleted — it must be free & helpful, like a video or web page or forum thread about this exact problem. NO FORUM HOMEPAGES. If you have a for-profit service, contact us .

Preview your link:

Not what you are looking for?

• Remember me Not recommended on shared computers

Forgot your password?

• Audio, Infotainment Navigation, MyGig, UConnect, etc.

Where is HFM (Hands Free module) located on Journey/Freemont?

• hands free module

By Valter J Sabater October 20, 2013 in Audio, Infotainment Navigation, MyGig, UConnect, etc.

• Reply to this topic
• Start new topic

Recommended Posts

Valter j sabater.

Hello. I got a problem, with my Freemont 2012, bluetooth and voice command. I press the "buttons" on the uconnect, and they just grey out, but nothing happens. Can't access phone settings also.

I already let the negative cable of the battery unplugged for about 12 hours, without solving it.

Than I took it to a dealer, but they didn't solve, they actually did nothing. They just upgraded the software and reseted it. So I will need to take it to another dealer (300km away).

So, reading thru several forums, the problem is probably the HFM module. Maybe just a problem with the connections, and unplugging and plugging again may solve.

I already checked behind the glove compartment and it is not there. I also looked bellow the panel at drivers side, and coundn't see it.

Does anyone know where is it really located?

Link to comment

Share on other sites.

Journeyman425

08 - Electrical/8E - Electronic Control Modules/MODULE, Hands Free/Description DESCRIPTION

The Hands Free Module (HFM) (3) (also known as the Bluetooth™ module) is found in vehicles equipped with the optional Uconnect® Hands-Free System. This module is located beneath the instrument panel and above the steering column. The HFM hardware and circuitry is contained and protected within a molded black plastic housing that has two integral mounts (2) and an integral locating pin (1). The HFM is positioned to a stamped metal steering column mounting bracket by the locating pin, then secured to the bracket by two screws.

The HFM has three integral connector receptacles that are oriented toward the dash panel when it is installed in the vehicle. The two largest receptacles (5 and 6) connect the HFM to the vehicle electrical system through dedicated take outs and connectors of the instrument panel wire harness. The smallest connector (4) accepts a Universal Serial Bus (USB) cable connector that connects the HFM to the Radio Receiver Module (RRM) (also known as the radio or the head unit).

The internal circuitry of the HFM includes a microcontroller, flash memory and a Bluetooth™ module. The module also includes sophisticated Voice Recognition (VR) software. The HFM software is flash programmable.

The HFM cannot be adjusted or repaired and, if damaged or ineffective, the entire HFM must be replaced.

The Hands Free Module (HFM) (1) is mounted above the steering column (3) and against the dash panel (4) to the underside of the instrument panel column support bracket.

• Disconnect and isolate the negative cable from the battery.
• Remove the knee blocker from the instrument panel steering column opening. (Refer to 23 - Body/Instrument Panel/KNEEBLOCKER - Removal) .

One of the HFM mounting screws is concealed between the forward (connector) side of the module and the dash panel.

• Remove the two screws (2) that secure the Hands Free Module (HFM) (1) to the underside of the instrument panel column support bracket.
• Lower the HFM far enough to access and disconnect the three wire harness connections (5) from the module connector receptacles.

For an unrelated project, I need to remove the lower dash panel, the one covering the steering column, maybe that's the one mentioned in point 3 above?

Unfortunately I cannot follow the link (since it asks to login).

Removing the two nuts on the lower side is not enough to remove the panel, what seems to be a screw cover on the top left (a rectangle), actually isn't, so I don't know if there is some hidden screw or if it's just a matter of pulling hard enough (but I fear I'll break the panel that way).

• 2 years later...

Kingsoulard

08 - Electrical/8E - Electronic Control Modules/MODULE, Hands Free/Description DESCRIPTION The Hands Free Module (HFM) (3) (also known as the Bluetooth™ module) is found in vehicles equipped with the optional Uconnect® Hands-Free System. This module is located beneath the instrument panel and above the steering column. The HFM hardware and circuitry is contained and protected within a molded black plastic housing that has two integral mounts (2) and an integral locating pin (1). The HFM is positioned to a stamped metal steering column mounting bracket by the locating pin, then secured to the bracket by two screws. The HFM has three integral connector receptacles that are oriented toward the dash panel when it is installed in the vehicle. The two largest receptacles (5 and 6) connect the HFM to the vehicle electrical system through dedicated take outs and connectors of the instrument panel wire harness. The smallest connector (4) accepts a Universal Serial Bus (USB) cable connector that connects the HFM to the Radio Receiver Module (RRM) (also known as the radio or the head unit). The internal circuitry of the HFM includes a microcontroller, flash memory and a Bluetooth™ module. The module also includes sophisticated Voice Recognition (VR) software. The HFM software is flash programmable. The HFM cannot be adjusted or repaired and, if damaged or ineffective, the entire HFM must be replaced. 08 - Electrical/8E - Electronic Control Modules/MODULE, Hands Free/Removal REMOVAL Labor Operations: Click to display a list of Labor Operations associated with this procedure NOTE: The Hands Free Module (HFM) (1) is mounted above the steering column (3) and against the dash panel (4) to the underside of the instrument panel column support bracket. Disconnect and isolate the negative cable from the battery. Remove the knee blocker from the instrument panel steering column opening. (Refer to 23 - Body/Instrument Panel/KNEEBLOCKER - Removal) . Remove the brake pedal assembly from the dash panel (4). (Refer to 05 - Brakes/Hydraulic/Mechanical/PEDAL(S) , Brake and/or Accelerator - Removal) . NOTE: One of the HFM mounting screws is concealed between the forward (connector) side of the module and the dash panel. Remove the two screws (2) that secure the Hands Free Module (HFM) (1) to the underside of the instrument panel column support bracket. Lower the HFM far enough to access and disconnect the three wire harness connections (5) from the module connector receptacles. Remove the HFM from above the steering column (3) and under the instrument panel.

Has your radio been serviced or has your dash been opened up for any reason? Before you disassemble the entire vehicle you might want to pull out the radio module (behind the hard buttons below the display screen) to make certain that the 2 USB connectors (one for the BT and the other for the USB connection in the console) are properly seated in their respective sockets. It is a simple 10 minute operation.

• 7 months later...

On 2/20/2016 at 4:37 AM, bramfrank said: Has your radio been serviced or has your dash been opened up for any reason? Before you disassemble the entire vehicle you might want to pull out the radio module (behind the hard buttons below the display screen) to make certain that the 2 USB connectors (one for the BT and the other for the USB connection in the console) are properly seated in their respective sockets. It is a simple 10 minute operation.

For us non-technical, how do you accomplish the above (simple 10 minute operation)?

You'll find detailed instructions at the start of the backup camera installation manual. Link here: http://starparts.chrysler.com/info/default/K6861161.pdf

• 3 years later...

journeytofix

Bramfrank... from so long ago - could you tell me which of these plugs is the Bluetooth module plug? Diagnosing a parasitic battery drain issue. 

On 9/18/2020 at 9:44 PM, journeytofix said: Bramfrank... from so long ago - could you tell me which of these plugs is the Bluetooth module plug? Diagnosing a parasitic battery drain issue. 

It is one of the two connectors identified as #4 - and they are interchangeable, so AFAIK the only real way to tell which is which is to disconnect one of them and see if that takes out the Bluetooth - if it does, you have found the right one. Note, for the sake of being careful it is a good idea to disconnect power before removing connections from the module.  It isn't likely to hurt anything if you don't, but one never knows and these things are expensive. 

• 5 months later...

I bought a used telematics module off eBay (supposedly for my 2012 Dodge Journey), installed it but it didn't rectify my no connection issue. I didn't mount it in place, could this be the reason it still doesn't connect? There is an integral locating pin on the mounting case, should I have mounted the module before testing it? I just left it hanging by the connectors while I tested if it connected or not. See item #1 in attached photo.  

Frustrating...

Is the case metal or plastic? If metal, might  be used as a ground. Obviously if plastic it shouldn’t matter...maybe your eBay unit is DOA....

buying a used electrical device online is a crap shoot. I never would myself.  Hopefully it has a warranty.

1 hour ago, OhareFred said: Is the case metal or plastic? If metal, might  be used as a ground. Obviously if plastic it shouldn’t matter...maybe your eBay unit is DOA....   buying a used electrical device online is a crap shoot. I never would myself.  Hopefully it has a warranty.

The case is plastic, I'm just wondering if this "integral locating pin" inserts into some type of switch or if it exists just to align up the module in its location.  Anyone know the answer to this?

The eBay seller has said ship the alleged DOA module back to him and will supposedly refund my return shipping and original charges. 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account. Note: Your post will require moderator approval before it will be visible.

×   Pasted as rich text.    Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.    Display as a link instead

×   Your previous content has been restored.    Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

• Insert image from URL
• Submit Reply
• Existing user? Sign In

More Forum Apps

• Online Users
• Leaderboard

|| Forum Activity ||

• All Activity
• Create New...

Home » Troubleshooting » Dodge Charger Bluetooth not working – causes and how to fix it

Dodge Charger Bluetooth not working – causes and how to fix it

Dodge Charger allows drivers and passengers to connect their smartphones, stream music, and make hands-free calls via Bluetooth. However, there are instances when the Bluetooth in Charger may encounter issues, leaving users frustrated and disconnected. In this article, we will explore common causes for car Bluetooth problems and provide practical solutions to get it up and running again.

Bluetooth, being one of the most popular wireless technologies, enables drivers to integrate their smartphones seamlessly with the car’s entertainment and communication systems. However, just like any technology, Bluetooth connections can encounter hiccups, leading to issues such as pairing failures, audio interruptions, and dropped connections. Understanding the underlying causes and knowing how to troubleshoot these problems is essential for a smooth and enjoyable driving experience.

1. Bluetooth is disabled

Verify bluetooth is enabled in the smartphone.

Before delving into complex troubleshooting steps, it’s essential to start with the basics. Ensure that Bluetooth is enabled on your iPhone or Android device. For most smartphones, you can access the Bluetooth settings through the quick settings menu or the main settings app. Turn on Bluetooth and keep your smartphone’s Bluetooth screen open as as you connect your phone to the infotainment system of Charger.

Verify Bluetooth is enabled in Charger

The next crucial step is to confirm that Bluetooth is enabled in the infotainment system of your Charger. Access the infotainment system’s settings and navigate to the Bluetooth or phone menu. Make sure it is turned on, and the infotainment system is actively searching for nearby devices.

2. Forget old pairings

If your smartphone has been connected to multiple Bluetooth devices in the past, it might be trying to connect to a previously paired device instead of your Charger infotainment system. To resolve this, go to your smartphone’s Bluetooth settings and look for any previously paired devices. Select “Forget” or “Unpair” for all the listed devices except your car’s infotainment system.

3. Restart Devices

Sometimes, Bluetooth connectivity issues can be resolved by a simple restart. Turn off both your smartphone and the infotainment system of your Charger. Wait for a few seconds and then turn them back on. This process can help clear any temporary glitches that might be affecting the Bluetooth connection.

4. Re-pair your phone

Re-pairing your phone with your Dodge Charger can be an effective solution for resolving persistent Bluetooth connectivity issues. Re-pairing essentially establishes a fresh connection between your smartphone and the car, which can help to clear any underlying glitches or conflicts.

Unpair the Existing Connection

Before re-pairing, you’ll need to remove the existing Bluetooth connection between your smartphone and Charger. This will ensure a clean slate for the re-pairing process.

Follow these general steps to unpair your phone:

• Go to the Bluetooth settings on your smartphone.
• Locate the list of paired devices and find the entry for your car’s infotainment system.
• Tap on the “Forget,” “Unpair,” or “Remove” option next to your car’s entry to disconnect it.
• Now re-connect your phone with the infotainment system via Bluetooth again.

5. Reset network settings

Resetting network settings on your smartphone is another troubleshooting step that can be beneficial in resolving Bluetooth connectivity issues with your Charger. This process resets all network-related settings, including Wi-Fi, cellular data, and Bluetooth configurations, to their default values. Here’s how you can reset network settings on both an iPhone and an Android device.

Reset Network Settings on iPhone:

• Open the Settings app on your iPhone.
• Scroll down and select “General.”
• Scroll to the bottom and tap on “Transfer or Reset iPhone.”
• Tap “Reset” on next screen.
• Choose “Reset Network Settings.”
• You may be prompted to enter your device passcode.
• Confirm the action by selecting “Reset Network Settings” again.
• Your iPhone will restart, and the network settings will be reset to their default values.

Reset Network Settings on Android device:

Specific steps may vary slightly based on the Android version and manufacturer.

• Open the Settings app on your Android device.
• Depending on your device and Android version, look for either “System,” “System & updates,” “System & Reset,” or “General management.”
• Select “Reset” or “Reset options.”
• Choose “Reset Wi-Fi, mobile & Bluetooth.”
• You may be asked to enter your device PIN or pattern.
• Confirm the action by selecting “Reset settings.”
• Your Android device will reset the network settings to their default state.

After resetting the network settings on your smartphone, you will need to reconfigure some network-related settings, such as Wi-Fi passwords and Bluetooth pairings. Make sure to pair your smartphone with the infotainment system of your Charger again and test the Bluetooth connectivity to see if the issue has been resolved.

Keep in mind that while resetting network settings can often fix connectivity issues, it may not always solve the problem, especially if the issue is hardware-related. If Bluetooth problems persist after trying this step, consider exploring other troubleshooting options.

6. Update Firmware and Software

Outdated firmware and software can lead to compatibility issues, resulting in Bluetooth problems. Check your car manufacturer’s website and your smartphone’s settings for available updates. Keeping both devices up-to-date can often resolve Bluetooth connectivity problems.

To update iOS on an iPhone, first, ensure you have a stable internet connection, and then connect your iPhone to a Wi-Fi network. Next, go to “Settings” on your iPhone and tap on “General.” From there, select “Software Update.” Your iPhone will check for the latest iOS update available. If an update is found, tap “Download and Install.” If prompted, enter your passcode.

Make sure your iPhone has enough battery life or keep it plugged in during the update. Once the download is complete, tap “Install” to begin the update process. Your iPhone will restart, and after a short while, the new iOS version will be installed, giving you access to the latest features, improvements, and bug fixes.

7. Factory reset the infotainment system

Performing a factory reset on your Charger infotainment system can be a viable solution to resolve persistent and complex Bluetooth issues that are not resolved through other troubleshooting methods. A factory reset will restore the system to its original settings, potentially clearing any software-related problems that were affecting the Bluetooth functionality. However, it’s important to remember that a factory reset will erase all personalized settings and data, so it should be considered as a last resort after trying other troubleshooting steps.

8. Try any other phone

If you’re experiencing Bluetooth connectivity issues in your Dodge Charger, trying a different phone can be a valuable troubleshooting step to isolate the problem. By connecting a different phone, whether it’s an iPhone or an Android device, you can determine whether the issue lies with your original smartphone or if it’s related to the car’s infotainment system.

Once the pairing process is complete, test the Bluetooth connection with the other phone. Make a hands-free call, play music, and use other Bluetooth functionalities to see if everything works as expected. If the connection works flawlessly with the other phone, it suggests that the issue might be with your original smartphone.

9. Hard reset your Charger

Disconnecting the main 12 volt battery of your Charger for about 15 minutes is another potential solution to resolve certain issues, including Bluetooth connectivity problems in the car’s infotainment system. This process is known as a “hard reset” and can help to clear any temporary glitches or errors that might be affecting various electronic systems in the vehicle, including the infotainment system.

Identify the Negative Terminal

The negative terminal on the battery is marked with a minus (“-“) sign and is usually colored black. Take note of its location.

Disconnect the Negative Terminal

Use a wrench or pliers to loosen and remove the bolt or clamp that secures the negative terminal to the battery post. Once loosened, carefully lift the negative terminal away from the battery post.

Wait for 15 Minutes

After disconnecting the negative terminal, leave the car’s battery disconnected for approximately 15 minutes. This will allow any residual electrical charge to dissipate and ensure a complete reset of the car’s electronic systems.

Reconnect the Negative Terminal

After the 15 minutes have elapsed, reattach the negative terminal to the battery post and tighten the bolt or clamp securely.

Start your Charger

With the battery reconnected, start the engine of your Charger and let it run for a few minutes. During this time, various electronic systems, including the infotainment system, will initialize and reestablish connections.

Test Bluetooth Connectivity

Once the car is running, test the Bluetooth connectivity by pairing your smartphone with the infotainment system of your Charger and using various Bluetooth features to ensure everything works correctly.

Remember that a hard reset by disconnecting the battery should be used as a last resort after trying other troubleshooting steps. While it can help in resolving certain issues, it may also result in the loss of some personalized settings in your Dodge Charger. If the Bluetooth problem persists or if you are unsure about performing a hard reset yourself, it’s best to seek assistance from a qualified mechanic or an authorized dealer to avoid any potential damage to the vehicle’s electrical system.

10. Hardware issue

If you have exhausted all software-related troubleshooting steps and Bluetooth connectivity issues persist with Charger, it is possible that the problem may be related to a hardware issue. Hardware problems can be more challenging to resolve and may require professional inspection and repair. Here are some indications that the issue might be hardware-related:

Persistent Issues

If you have experienced Bluetooth problems consistently, even after trying various software fixes and different smartphones, it could be a sign of a hardware problem.

Inconsistent Connectivity

If the Bluetooth connection frequently drops or becomes unstable, it may be due to hardware-related issues within the Charger infotainment system.

No Devices Detected

If the infotainment system in Charger is unable to detect any Bluetooth devices, including smartphones and other accessories, it might be an indication of hardware failure.

Audio Quality Issues

If you experience distorted or poor audio quality during Bluetooth calls or music playback, it could be due to hardware problems with the Bluetooth module or related components.

If you suspect a hardware issue, it’s best to contact your car’s manufacturer or authorized service center for further assistance. They have the expertise and tools to diagnose and repair hardware problems accurately. Depending on the vehicle’s warranty status and the nature of the issue, the manufacturer may cover the repair costs.

Before seeking professional help, you can also check for any software or firmware updates specific to your car’s infotainment system. Occasionally, manufacturers release updates to address known hardware-related issues, and updating the system might resolve the problem.

Bluetooth connectivity issues between your smartphone and the infotainment system of Dodge Charger can be frustrating, but they are usually easily resolved by following a few troubleshooting steps. Ensuring Bluetooth is enabled on both devices, pairing them correctly, and checking for updates are essential starting points. Restarting or resetting devices can also help establish a stable connection. Remember to stay patient and methodical when troubleshooting, as the solution is often just a few simple steps away.

• Nissan X-Trail key fob won’t lock or unlock the doors
• VW Golf makes clicking noise and won’t start – causes and how to fix it
• Chevy HHR ABS light is on – causes and how to reset
• Dodge Challenger uneven tire wear causes
• Chevy Orlando check engine light is on – causes and how to reset
• Peugeot 5008 AC not cooling – causes and diagnosis
• Kia Sorento pulls to the left when driving
• Cadillac CT6 bad gas mileage causes and how to improve it
• Lamborghini Huracan engine overheating causes and how to fix it
• Ford Explorer AC not working – causes and how to fix it
• Fiat 124 Spider dashboard lights flicker and won’t start – causes and how to fix it
• Volvo V60 bad wheel speed sensor symptoms – how to diagnose
• How to set up service reminder intervals on Hyundai Palisade
• BMW 3 Series low oil pressure light is on – causes and how to reset
• Peugeot Rifter AC smells bad – causes and diagnosis
• SEAT Ibiza shakes at highway speeds – causes and how to fix it
• Ford Everest AC blower motor not working – causes and diagnosis
• Land Rover Discovery Sport bad O2 sensor symptoms, causes, and diagnosis
• BMW 740i won’t start – causes and how to fix it
• Skoda Rapid AC not blowing hard enough – weak airflow causes